Pi 5 with latest Pi OS desktop updated to this morning. 2 TB NVMe SSD in RTL9210 USB 3 enclosure. Not recognised. Nothing in dmesg.
rpi-update this morning to test the mod for A2 cards. Added the /boot/firmware/config.txt change for A2 cards. tested. Then ran regular software update. No other changes. I used the SSDs mentioned here in a Pi 4 last year as storage, not boot drives.
Here is dmesg for the same SSD plugged into an up to date Linux Mint.
rpi-update this morning to test the mod for A2 cards. Added the /boot/firmware/config.txt change for A2 cards. tested. Then ran regular software update. No other changes. I used the SSDs mentioned here in a Pi 4 last year as storage, not boot drives.
Here is dmesg for the same SSD plugged into an up to date Linux Mint.
Similar enclosure with 512 GB SSD and same RTL9210 chip in the Pi 5:[ 8279.092918] usb 4-3: new SuperSpeed USB device number 4 using xhci_hcd
[ 8279.126717] usb 4-3: New USB device found, idVendor=0bda, idProduct=9210, bcdDevice=30.00
[ 8279.126723] usb 4-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8279.126726] usb 4-3: Product: RTL9210
[ 8279.126728] usb 4-3: Manufacturer: Realtek
[ 8279.126730] usb 4-3: SerialNumber: 012345678909
[ 8279.129533] usb 4-3: Enable of device-initiated U1 failed.
[ 8279.130172] usb 4-3: Enable of device-initiated U2 failed.
[ 8279.190289] usb 4-3: Enable of device-initiated U1 failed.
[ 8279.190758] usb 4-3: Enable of device-initiated U2 failed.
[ 8279.192809] scsi host0: uas
[ 8279.197716] scsi 0:0:0:0: Direct-Access Realtek RTL9210 NVME 1.00 PQ: 0 ANSI: 6
[ 8279.230182] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 8279.235570] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 8279.238321] sd 0:0:0:0: [sda] Write Protect is off
[ 8279.238323] sd 0:0:0:0: [sda] Mode Sense: 37 00 00 08
[ 8279.243461] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8279.245103] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[ 8279.245104] sd 0:0:0:0: [sda] Optimal transfer size 33553920 bytes
[ 8279.261382] sda: sda1
[ 8279.261508] sd 0:0:0:0: [sda] Attached SCSI disk
[ 8279.428902] EXT4-fs (sda1): mounted filesystem 5eceeb1a-845f-42da-8c45-044b2fbfb0a0 r/w with ordered data mode. Quota mode: none.
Here is the 512 GB SSD in Linux Mint.[ 454.447991] usb 2-1: new SuperSpeed USB device number 3 using xhci-hcd
[ 454.480403] usb 2-1: New USB device found, idVendor=0bda, idProduct=9210, bcdDevice=20.01
[ 454.480408] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 454.480411] usb 2-1: Product: RTL9210
[ 454.480414] usb 2-1: Manufacturer: Realtek
[ 454.480416] usb 2-1: SerialNumber: 012345678904
[ 454.484789] usb 2-1: Enable of device-initiated U1 failed.
[ 454.485164] usb 2-1: Enable of device-initiated U2 failed.
[ 454.500294] usb 2-1: Enable of device-initiated U1 failed.
[ 454.500663] usb 2-1: Enable of device-initiated U2 failed.
[ 454.501647] scsi host0: uas
[ 454.505122] scsi 0:0:0:0: Direct-Access Realtek RTL9210 NVME 1.00 PQ: 0 ANSI: 6
[ 454.536548] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 454.694842] sd 0:0:0:0: [sda] 1000215216 512-byte logical blocks: (512 GB/477 GiB)
[ 454.696306] sd 0:0:0:0: [sda] Write Protect is off
[ 454.696310] sd 0:0:0:0: [sda] Mode Sense: 37 00 00 08
[ 454.699656] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 454.700907] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[ 454.700911] sd 0:0:0:0: [sda] Optimal transfer size 33553920 bytes
[ 454.713230] sda: sda1
[ 454.713363] sd 0:0:0:0: [sda] Attached SCSI disk
[ 455.251474] EXT4-fs (sda1): mounted filesystem 05d16310-5d0b-49bb-887a-2a0476174f22 r/w with ordered data mode. Quota mode: none.
For reference, this is the RTL9210 with no SSD inserted:[ 8888.255619] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd
[ 8888.283668] usb 4-3: New USB device found, idVendor=0bda, idProduct=9210, bcdDevice=20.01
[ 8888.283677] usb 4-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8888.283680] usb 4-3: Product: RTL9210
[ 8888.283682] usb 4-3: Manufacturer: Realtek
[ 8888.283685] usb 4-3: SerialNumber: 012345678904
[ 8888.286610] usb 4-3: Enable of device-initiated U1 failed.
[ 8888.286938] usb 4-3: Enable of device-initiated U2 failed.
[ 8888.295321] usb 4-3: Enable of device-initiated U1 failed.
[ 8888.295764] usb 4-3: Enable of device-initiated U2 failed.
[ 8888.297484] scsi host0: uas
[ 8888.300889] scsi 0:0:0:0: Direct-Access Realtek RTL9210 NVME 1.00 PQ: 0 ANSI: 6
[ 8888.326188] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 8888.329571] sd 0:0:0:0: [sda] 1000215216 512-byte logical blocks: (512 GB/477 GiB)
[ 8888.331435] sd 0:0:0:0: [sda] Write Protect is off
[ 8888.331448] sd 0:0:0:0: [sda] Mode Sense: 37 00 00 08
[ 8888.334688] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8888.335949] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[ 8888.335953] sd 0:0:0:0: [sda] Optimal transfer size 33553920 bytes
[ 8888.473153] sda: sda1
[ 8888.473293] sd 0:0:0:0: [sda] Attached SCSI disk
[ 8889.158648] EXT4-fs (sda1): mounted filesystem 05d16310-5d0b-49bb-887a-2a0476174f22 r/w with ordered data mode. Quota mode: none.
[ 325.291680] usb 1-1: new high-speed USB device number 4 using xhci-hcd
[ 325.450084] usb 1-1: New USB device found, idVendor=0bda, idProduct=9210, bcdDevice=21.00
[ 325.450090] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 325.450093] usb 1-1: Product: M.2 NVME
[ 325.450096] usb 1-1: Manufacturer: External
[ 325.450098] usb 1-1: SerialNumber: 012345678905
[ 325.496854] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 325.497038] scsi host0: usb-storage 1-1:1.0
[ 326.504204] scsi 0:0:0:0: Direct-Access External M.2 NVME 1.00 PQ: 0 ANSI: 6
[ 326.504485] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 326.518262] sd 0:0:0:0: [sda] Read Capacity(10) failed: Result: hostbyte=0x00 driverbyte=DRIVER_OK
[ 326.518270] sd 0:0:0:0: [sda] Sense Key : 0x5 [current]
[ 326.518273] sd 0:0:0:0: [sda] ASC=0x20 ASCQ=0x0
[ 326.521734] sd 0:0:0:0: [sda] 0 512-byte logical blocks: (0 B/0 B)
[ 326.521738] sd 0:0:0:0: [sda] 0-byte physical blocks
[ 326.525157] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
[ 326.528636] sd 0:0:0:0: [sda] Asking for cache data failed
[ 326.528639] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 326.528947] sd 0:0:0:0: [sda] Attached SCSI removable disk
Statistics: Posted by peterlite — Thu May 30, 2024 7:22 am